The holders to allow our LED bars to be mounted in your existing waterproof tube sockets.
€10.99*
Available, delivery time: 1-3 days
These brackets are used to fix our LED bars in existing T5 or T8 moisture-proof sockets. Two versions are available: SOLO and DUO.
SOLO is used to fix one LED bar per tube.
The DUO brackets are used for mounting two LED bars per tube.
The brackets have a universal length, are mounted at the ends of the LED bar and can be extended and adjusted to the tube length if required. The table below shows which fluorescent tubes can be replaced with the respective LED bars. As a small highlight, the LED bars incl. holder can be rotated 360° in the tube sockets, so you can also set special accents if required, e.g. special lighting of the rear wall, etc.
Please note:
Fluorescent tubes |
...compatible with... |
eco+ LED bars |
PRO² LED bars |
---|---|---|---|
361 to 438 |
... |
20cm, 30cm |
/ |
549 to 590 |
... |
20cm, 30cm, 50cm |
47cm |
849 to 895 |
... |
50cm, 80cm |
47cm, 67cm, 75cm |
1047 |
... |
80cm, 100cm |
75cm, 96cm |
1149 |
... |
100cm |
96cm, 106cm |
1200 |
... |
100cm, 116cm |
106cm |
1449 to 1500 |
... |
116cm, 120cm, 140cm |
135cm |
Suitable only for ordinary waterproof tube sockets! Not compatible with the aquaLUMix lights! The tube sockets may only be used in future as holders for LED bars! The previous power supply to your fluorescent tube lighting must be permanently disconnected and will not be needed in future! The power is supplied by an external LED mains adapter. (see Accessories) The supplied blue protective sleeves prevent the penetration of moisture and protect the electrical contacts of your fluorescent tube lighting sockets.
Scope of supply: 1 Pair Mounting rails, protective sleeves, fastenings
Possible configuration of the holders with LED bars: There are many different possible combinations. It is important that at least one LED bar forms a connection between the two mounting rails. The distance between the mounting rails varies according to the tube length and the LED bar.
Videos
10 of 49 reviews
4.86 out of 5 stars
Login
16 December 2020 16:57
sehr gut
passt alles zusammen und hält die Lampen prima im Aquarium
25 December 2018 13:20
Einfach!
lässt sich einfach in die "alte" T8 Fassung montieren und lässt sich bewegen wie man die Ausleuchtung haben möchte.
27 September 2017 10:41
einfach gut
so einfach zu benutzen wirklich eine tolle Ideees gibt was her vielfältig einsetzbar
11 November 2015 10:21
Gut durchdacht.
Passt perfekt, gut einzustellen. Allerdingstsind die kleinen nix für Bauarbeiterhände. Lässt sich aber whrscheinlich nicht anders lösen.
8 December 2023 20:22
Ideal zum Nachrüsten
Ideal zum Nachrüsten
23 March 2020 18:14
Ganz wichtig um T5 Neonröhrenhalterung zu verwenden!
Nach der tollen kompetenten Beratung plus dem Sammelangebot habe ich so bestellt und alles passt wie angegossen! Vielen Dank!
16 November 2018 11:17
gut durchdacht
einfache Montage
8 March 2017 11:11
Super
Einfach abmessen, LED Leiste aufschrauben. Fertig. Einfacher geht es nicht.
4 September 2016 21:05
schnell und einfach
Das anbringen ist in wenigen Minuten erledigt.
30 September 2015 14:22
Alles super
Super Service ,gerne wieder.
Customers also bought
High-performance LED switching mains adapter for operating our LED lighting bars (12V DC)
This distributor allows several LED lighting bars to be operated with a single mains adapter (assuming the power output is adequate).
The CleanCover protects the LED bar from limescale and dirt deposits and is very easy to clean. A splashwater protection, made of highly transparent, ultra-thin, impact-resistant plastic.
Are you unsure whether the selected products are compatible with each other or whether something important has been forgotten?
High-performance LED switching mains adapter for operating our LED lighting bars (12V DC)
Our smallest model offers all the basic functions of a light control system - simplicity in operation!
Similar products
The holders to allow our LED bars to be mounted in your existing waterproof tube sockets.
For easy bundling and guidance of cable lines.
The holders to allow our LED bars to be mounted in your existing waterproof tube sockets.
With this set up to 6 eco+/PRO² LED bars can be easily fixed in the aquarium cover or the LED adapter profile for JUWEL and EHEIM aquariums.
The LED adapter profile replaces your existing conventional T5 or T8 batten fittings 1 for 1
The holders to allow our LED bars to be mounted in your existing waterproof tube sockets.
To replace light bars and cover flaps, the frame of the existing cover is still used.
Additional holding bridges for individual mounting of several (shorter) LED bars
Customers also viewed
The holders to allow our LED bars to be mounted in your existing waterproof tube sockets.
The holders to allow our LED bars to be mounted in your existing waterproof tube sockets.
The holders to allow our LED bars to be mounted in your existing waterproof tube sockets.
To replace light bars and cover flaps, the frame of the existing cover is still used.
Experience cool white-blue light with the eco+ LED bars. Natural and favored for Malawis and Tanganjika Cichlids. Explore the possibilities!
Experience the warmth of the SUNSET LED bars with 3500K, perfect for plants and sunrise and sunset simulations. Find your ideal combination!
The LED adapter profile replaces your existing conventional T5 or T8 batten fittings 1 for 1